How-To
Set Screw Point Types: How to Choose Cup, Flat, Cone, Dog or Oval
By the Fastenio team · · 7 min read
Pick the set screw point by what it has to do to the shaft. A cup point is the general-purpose default: it bites into the shaft surface for a semi-permanent hold. A flat point or oval point is the choice when the shaft must not be marked, when it is hardened, or when you will loosen and reset the part often. A cone point is for a permanent position, driven into soft material or seated in a spot drilled into the shaft. A dog point has a cylindrical tip that drops into a matching hole or slot to key the part in place.
So the real question is what the shaft can take. If you can't drill or mark it, start with flat or oval. If you can drill a spot or hole, cone or dog points give you a fixed location. If neither matters, use a cup point. Fastenio's socket set screws come in all of these points with an Allen hex socket drive, in 18-8 and 316 stainless steel.
What are the set screw point types, and what does each one do?
A set screw is a headless, fully threaded screw that runs into a tapped hole in a collar, pulley or hub and presses its point against the shaft inside. The point is the only part touching the shaft, so it decides how the screw holds and what it leaves behind. Here is how Fastenio's product pages describe each point:
| Point | What it does | Shaft prep | Marks the shaft? |
|---|---|---|---|
| Cup | Bites into soft or hard surfaces for a semi-permanent hold | None | Yes, it bites in |
| Flat | Seats against a hard, flat surface without marring or embedding | A flat surface to bear on | No |
| Oval | Rounded tip for frequent adjustment, or seating in a groove | None, or a groove | Minimal |
| Cone | Penetrates soft material or a matching spot for a permanent, anti-rotation position | A drilled spot, unless the material is soft | Yes, it penetrates |
| Full dog | Long cylindrical tip seats in a matching hole or slot to key a part to a shaft | A drilled hole or slot | Only the hole you drill |
| Half dog | Shorter cylindrical tip seats in a drilled spot or slot | A drilled spot or slot | Only the spot you drill |
Sources: the descriptions on the cup, flat, oval, cone, full dog and half dog product pages linked from the set screws category. Inch set screws there are made to ASME B18.3; the dog point parts are metric, to DIN 915 / ISO 4028.
Which set screw point should you use by default?
Use a cup point unless something rules it out. It needs no shaft prep, and it works on soft or hard surfaces. On the set screws category it is the only point listed across the whole inch range in 18-8 stainless, from #4-40 up to 3/4-10, and it is the only point listed in inch sizes in 316.
The trade-off is the mark it leaves. A cup point bites into the shaft, so it is the wrong choice for a shaft you can't mark or a part you will move to a new position often. That is where flat and oval points come in.
Which point should you use on a hardened shaft or a shaft you can't mark?
Use a flat point. Fastenio's flat point product page describes it as seating against a hard, flat surface without marring or embedding, and names "setting against a hardened shaft" and "frequently repositioned" parts as what it is for. Note the wording: it is described as bearing on a flat surface.
An oval point is the other option when marks matter. Its product page describes a rounded tip "for frequent adjustment with minimal shaft marking, or seating in a groove". That makes it a good fit for a part you adjust often or one that rides in a groove cut around the shaft.
Sources don't agree on whether flat or oval repositions better, and no standard settles it, so pick by the shaft: flat point against a flat, oval point on a round surface or in a groove.
When should you use a cone point or a dog point instead?
Use these when the part must stay in one exact position and you are able to prepare the shaft.
- Cone point: the sharp tip penetrates soft material or a matching spot drilled into the shaft. The product page describes it as giving "high holding power and permanent, anti-rotation location". Choose it for a pulley or collar that should never move once it's set.
- Full dog point: a cylindrical tip that sticks out past the threads and drops into a matching hole or slot. The product page calls it "ideal for keying a component to a shaft", with "high shear holding". Because the tip sits in a hole rather than pressing on the surface, the position is set by the hole you drill.
- Half dog point: a shorter cylindrical tip that seats in a drilled spot or slot "for positive location". Use it where a full dog would be longer than the hole needs.
Which set screw point holds best?
There is no single answer you can trust as a number. Holding-power tables for set screws are widely copied, but they come from manufacturer and distributor catalogs, not from ASME B18.3. This article doesn't print them.
What the product pages do say is directional: cup point gives a "semi-permanent hold", cone point "high holding power", and dog points "high shear holding" when seated in a hole. If the joint carries real load, size it from the screw manufacturer's data for your exact part, or key the part with a dog point in a drilled hole so the position doesn't depend on surface grip alone.
Can you use stainless set screws in a stainless hub?
Yes, but watch for galling. A stainless screw running into a stainless tapped hole is the same-material pairing that makes threads seize. Put a nickel-based or metal-free anti-seize on the threads and run the screw in slowly. The full list of steps is in how to prevent stainless steel galling.
On grade: 18-8 is the standard stainless for outdoor and wet environments, and 316 is the choice for salt water, pools and chemical exposure, according to the grade notes on the set screws category. If you're unsure which you need, the 18-8 vs other stainless grades guide explains the difference.
What do you need to specify when ordering set screws?
Four things, in this order:
- Thread size and pitch, for example 1/4-20 or #10-32. Match it to the tapped hole in the hub. If you're not sure whether the hole is coarse or fine thread, check it against the thread pitch chart.
- Length. Measure from the outside of the hub to the shaft, and pick a length that reaches the shaft without sticking out of the hub.
- Point type, from the table above.
- Material, 18-8 or 316 stainless steel.
What the set screws category lists in inch stainless sizes today:
| Point | 18-8 inch sizes | 316 inch sizes |
|---|---|---|
| Cup | #4-40, #5-40, #6-32, #8-32, #10-24, #10-32, 1/4-20, 1/4-28, 5/16-18, 5/16-24, 3/8-16, 3/8-24, 7/16-14, 7/16-20, 1/2-13, 1/2-20, 5/8-11, 3/4-10 | #8-32, 1/4-20, 5/16-18, 3/8-16, 1/2-13 |
| Cone | #6-32, #8-32, #10-32, 1/4-20 | none listed |
| Flat | 5/16-18, 3/8-16 | none listed |
| Oval | 3/8-16 | none listed |
| Full dog / half dog | metric sizes only | none listed |
Source: product rows on /catalog/set-screws, November 2026. Check the product page for the lengths and hex key size of the exact part you need.
Set screws use the same Allen hex socket drive as socket head cap screws, so the same kind of hex key drives both. If you need a head to grip or a part that sits proud of the hub, a socket head cap screw is the alternative.
What if the hex socket strips?
A worn or undersized hex key can round out a set screw's socket. Use a full-length key that bottoms out in the socket and replace it when the corners round. If the socket is already stripped, the fixes for a rounded hex socket, from tapping in the next size bit to an extractor, are in how to remove a stripped screw.
Bottom line
Default to a cup point. Switch to flat (against a flat or a hardened shaft) or oval (round shaft or groove) when you can't mark the shaft or will adjust the part often. Use a cone point in a drilled spot for a permanent position, and a dog point in a hole or slot to key the part. Specify thread, length, point and grade, and anti-seize stainless-on-stainless threads.
Shop socket set screws by point, size and grade, and socket head cap screws when you need a head.
Keep reading
- How to Remove a Stripped Screw (and Stop Stripping Them)
Start with the method that does the least damage and only step up when it fails.
- Fully Threaded Stud vs. Threaded Rod vs. Double-End Stud
A fully threaded stud and threaded rod are the same idea, a headless part threaded end to end; the name mostly follows the length and how it's sold. A double-end stud is different: threaded at both ends with a plain middle.
- Can You Use Stainless Steel Screws in Aluminum? (Galvanic Corrosion)
Stainless screws in aluminum are common and usually fine when the joint stays dry. Once water bridges the two metals, the aluminum around the screw corrodes, not the screw. Keep water out, isolate the contact, and don't put a big stainless part on a small piece of aluminum.