Comparisons
Fully Threaded Stud vs. Threaded Rod vs. Double-End Stud
By the Fastenio team · · 6 min read
A fully threaded stud and threaded rod are the same idea: a headless length of metal threaded from one end to the other. The difference is mostly in how they're sold. "Stud" usually means a part already cut to a specific length, and "threaded rod" (or all-thread) usually means long stock you cut yourself. A double-end stud is a different part: it is threaded at both ends with an unthreaded section in the middle, and the two ends often have different thread lengths.
Suppliers use these names loosely, so don't buy on the name alone. Check the diameter and thread pitch, the overall length, and whether the part is threaded all the way or only at the ends. Fastenio sells stainless steel fully threaded studs and double-end studs in 18-8 and 316; it does not carry threaded rod.
What is the difference between a fully threaded stud and threaded rod?
Shape-wise, nothing. Both are continuously threaded with no head, so a nut runs on from either end and can sit anywhere along the length. Fastenio's fully threaded stud category describes the part as headless, continuously threaded end to end, for tapped holes, nuts and couplers, and names ASME B18.31.2 as the standard.
The practical difference is length and handling:
| Fully threaded stud | Threaded rod (all-thread) | Double-end stud | |
|---|---|---|---|
| Threads | End to end | End to end | Both ends only, plain middle |
| Head | None | None | None |
| Usually sold as | Cut to a set length | Long stock, cut on site | Set length, set thread length at each end |
| Thread lengths per end | Not applicable | Not applicable | Often different (listed separately) |
| Fastenio carries | Yes | No | Yes, including tap-end studs |
If you have been cutting rod to the same short length over and over, a pre-cut stud in that length saves the cutting.
What is a double-end stud?
A double-end stud has two threaded sections separated by a plain shank. Fastenio's double-end stud listings print the two thread lengths separately on each row. Some have equal ends: the 3/4-10 x 3-1/2 in stud lists 1-1/2 in + 1-1/2 in of thread. Others are unequal: one 1/4-20 x 2-1/2 in stud lists 3/4 in + 1-1/2 in. The same category also lists tap-end studs.
If one end goes into a tapped hole and the other takes a nut, the two thread lengths are what decide the fit. When your drawing gives both thread lengths, match the row to them rather than picking the closest overall length.
When should you use a fully threaded stud?
Pick a fully threaded stud when the nut position has to be adjustable or when you need thread everywhere along the part:
- Through-bolting with a nut on each side. A stud passes through both parts and takes a nut and washer at each end. Because it is threaded all the way, the same stud works over a range of joint thicknesses.
- Into a tapped hole. One end goes into the threaded hole, and a nut on the exposed end does the clamping. The catalog page lists tapped holes among the stud's uses.
- Spacers, standoffs and adjustment. Nuts on either side of a panel let you set and lock its position anywhere along the stud. To keep a nut from backing off, the jam nut post covers the two-nut method.
- Extending a stud or bolt. Fastenio's hex coupling nuts are described as long hex nuts for joining threaded rod or extending a bolt or stud. If a run is longer than the longest stud in the size you need, two studs and a coupling nut are one way to cover it.
When should you use a double-end stud instead?
Use a double-end stud when the design calls for set thread lengths at each end. If you are replacing a part, measure both thread lengths and the overall length of the old stud (or read them off the drawing) and match all three. A fully threaded stud of the same diameter, pitch and length will often fit physically, but it isn't the same part, so check with whoever owns the drawing before you substitute.
What sizes and grades are available?
Sizes below are those listed on the two category pages on 2026-11-18; threads per inch come from the size callout and are confirmed against the thread pitch chart. Both categories also list one metric size (an M12 DIN 976A stud in A4/316 and an M16 DIN 939 double-end stud in A2/18-8).
| Size | Major diameter (in) | TPI | Thread series | Fully threaded studs | Double-end studs |
|---|---|---|---|---|---|
| #6-32 | 0.138 | 32 | UNC | 18-8 | — |
| #8-32 | 0.164 | 32 | UNC | 18-8 | — |
| #10-24 | 0.190 | 24 | UNC | 18-8, 316 | — |
| #10-32 | 0.190 | 32 | UNF | 18-8 | — |
| 1/4-20 | 0.250 | 20 | UNC | 18-8, 316 | 18-8, 316 |
| 5/16-18 | 0.3125 | 18 | UNC | 18-8, 316 | 18-8 |
| 3/8-16 | 0.375 | 16 | UNC | 18-8, 316 | 18-8 |
| 3/8-24 | 0.375 | 24 | UNF | 18-8 | — |
| 1/2-13 | 0.500 | 13 | UNC | 18-8, 316 | — |
| 5/8-11 | 0.625 | 11 | UNC | 18-8 | — |
| 3/4-10 | 0.750 | 10 | UNC | 18-8, 316 | 18-8 |
| 1-8 | 1.000 | 8 | UNC | — | 18-8 |
Not every length exists in every size and grade, so filter the category page by size and length. For grade choice, the catalog describes 18-8 as the standard stainless for outdoor and wet environments, not suited to salt water or harsh chemicals, and 316 as the grade chosen for salt water, pool and chemical exposure, where 18-8 can pit over time. The 18-8 vs. other grades guide goes further.
How do you order the right stud?
Treat a stud like any other threaded fastener and specify four things:
- Diameter and thread pitch, written as a callout such as 3/8-16. Coarse (UNC) is the default; fine (UNF) sizes like #10-32 and 3/8-24 are listed separately, and a coarse nut will not run on a fine stud. The bolt specifications post explains each part of the callout.
- Overall length. Suppliers don't all measure studs the same way, so if the length is critical, measure a sample or check the drawing. The measuring post covers the tools.
- Thread length at each end, for a double-end stud only.
- Grade: 18-8 or 316, matched to the environment.
Then match the nuts. The nut has to share the stud's diameter, pitch and grade; how to match nuts and bolts walks through it, and the same rules apply to studs. For through-bolting, you need two hex nuts per stud, and usually a flat washer under each.
Do stainless studs need anything special?
The same care as any stainless thread. A stainless nut on a stainless stud can gall. Lubricate the threads with anti-seize, run the nut down slowly, and avoid impact drivers for final tightening; the galling post has the full list.
The bottom line
A fully threaded stud is threaded rod cut to a set length; buy the stud when you know the length, and use a coupling nut if you need to go longer. A double-end stud is a different part, with two set thread lengths and a plain middle, for designs that call for it. Specify diameter and pitch, length, thread lengths (double-end only) and grade, then match the nuts. Shop stainless fully threaded studs, double-end studs, hex nuts and hex coupling nuts.
Keep reading
- Lock Washer vs. Lock Nut: Which to Use Under Vibration, and Why
If a joint keeps working loose, a lock nut is usually the better fix than a split washer.
- Stainless Steel Galling: Why Bolts Seize and How to Prevent It
Galling turns a nut and bolt into one piece of metal. Here's how to stop it before it starts.
- Can You Use Stainless Steel Screws in Aluminum? (Galvanic Corrosion)
Stainless screws in aluminum are common and usually fine when the joint stays dry. Once water bridges the two metals, the aluminum around the screw corrodes, not the screw. Keep water out, isolate the contact, and don't put a big stainless part on a small piece of aluminum.